[kjkrow]

Such is the price you pay for living in the Gorge

 

[Richy_T]

Broke the tail plastics by overloading the Renntec rack

 

[galahad05]

Broke the tail plastics by overloading the Renntec rack

Time for a Harbor Freight plastic welding kit?

 

[Richy_T]

Can I just buy some plastic wire for my MIG welder? Would that make it a PIG welder?

;D

 

[mg66]

Can I just buy some plastic wire for my MIG welder? Would that make it a PIG welder?

;D

Yep its hard to get the initial arc but then it welds just fine

 

[02SVSRIDER]

Yesterday I ordered a case, steel, and some red and yellow LED light strips, so I can make my rack and top case.

 

[Tuck_a_da_Phil]

Today I installed the new sprockets I got last week. 16T front and 43T rear. Man, it's just down right nasty on take-off now. It takes a some work to keep the front end down under hard acceleration even in 3rd gear. Now I just need to find a stump that needs pulling. I imagine my feelings will be hurt at the gas pump from now on but it's well worth the loss in mileage for the extra boost in acceleration.

 

[kjhilsinger]

Luis and I put my tank pad and my SpecTech grip pads on:

 

[aspicer]

installed my frame and swing arm sliders i just got from Blair.

another notch in my belt.

 

[Herzuki]

The Rizoma Zero 11's arrived today. So, now I'm really drooling and anxious to start installing the shock, LED's, throttle cables, etc. Whoooooooooo, Hoooooooooooooo! Happy Girl, Happy Girl.

 

[Tuck_a_da_Phil]

Luis and I put my tank pad and my SpecTech grip pads on:

Those tank grips look sweet. I especially like the black on the white bike. Where did you get those? Do they come in clear (I like the black but don't think it would look good on Copper.

 

[kjhilsinger]

Those tank grips look sweet. I especially like the black on the white bike. Where did you get those? Do they come in clear (I like the black but don't think it would look good on Copper.

They are TechSpec pads. I ordered them off Ebay. They have a precut set and a pair of 7"x13" squares. I ordered the squares, Luis drew the pattern, I cut them out, Luis stuck them on, and I still had enough left to make a grip pad for the seat cowel. I am pretty sure they dont have clear.

http://www.techspec-usa.com/

 

[warrenpridgeon]

Not today...but the weekend that just passed...
What I did to my SV was TAKE IT TO THE TRACK :-D
http://forum.svrider.com/showthread.php?t=109584

 

[Nudist]

gave it to nudist to have some suspension work done...

Working on it right now!

 

[Lost1888]

Just got home from a nice 60 mile loop I rode. Meet up with Chevellefan along the way.

 

[MBIKEN]

caught it on fire... JK got a pic of the squid lights..

 

[LSCYCLING]

cleaned the spark plug drain hole pulled the plug cleaned it out put in an old plug I still had, put on some dielectric grease and got the SV325 back up to 650. Then rode to work but found my front brake apparently has a leak or something as they are now squishy again. hmmmm.

 

[kjkrow]

Just took off the airbox to get at some of the harness, then bought some new wire to see if I can isolate my turn signal glitch. **** electrical gremlins are frustrating.

 

[Zokambaa]

don't see the lights... but if you are going to run the bike that lean, you are going to have to ride it like a granny... that engine looks like it is a weeee bit too warm :nana:

caught it on fire... JK got a pic of the squid lights..

 

[SexYonMySV]

Looked at the track bike....frustrated with the body work:

Then loving looked at my street bike. Decided to ride her down to the beach!;D