Suzuki SV650 Riders Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. SV650 Gen1 (99-02) Tech
    Purchased a 2000 SV650 a few months ago. Only went on two rides before getting a carb kit and rejetting it due to full aftermarket exhaust from PO. The two rides i went on were very promising. Tons of power, couldnt keep the front wheel down on full throttle in first gear and when shifting to...
  2. SV650 Gen1 (99-02) Tech
    Hi all. I bought a non running non cranking SV last year to fix up and have finally got it running last month. The previous owner told me he had fallen and dropped it on the side and could never get it back up and running. It will now start and run fine with the choke on and a spritz of starting...
  3. Electrical
    Hi, I recently got a project Sv650 that has a no power issue I know it has to do with the starter solenoid in some way but I’m running in circles here as I’m not the greatest with electrical. The 30A fuse has blown 2x, just sitting in getting battery voltage across the switch but the second I...
  4. SV650 Gen1 (99-02) Tech
    Hello guys, I'm new to the forum, the SV and motorcycling in general. I'm picking my first bike in a couple of days, but I can't find frame sliders or engine guards for it. (I live in Bulgaria) Can I use frame sliders for the 2nd gen? For some other bike? I'm too uneasy riding it without...
  5. SV650 Gen1 (99-02) Tech
    So I have been struggling with this issue for days now. I rebuilt my carburetors with an all balls kit, which honestly seemed to have gone well. I go to synchronize them, and I get zero vacuum on the rear carb but normal levels at the front. I thought it was a problem with my gas tank because I...
  6. Electrical
    Hello all, new to the forum and recently purchased a 2000 sv650. The bike has the integrated taillight/ brake and turn signals and it looks like the previous owner wired in what may be a trailer flasher to used leds? But there was 1 led bulb 1 incandescent in the sockets. I pulled the trailer...
  7. Accessories For Sale
    The SW-MOTECH Rack is for a 1st Gen SV. It is in very good condition. There are five small brackets that bolt on the bike and then the racks mount and dismount from the brackets with half-turn cam-lock screws in less than a minute. It is an excellent design. The racks are set up for GIVI...
  8. SV650 Gen1 (99-02) Tech
    What's up! Today I was trying to remove the magneto/flywheel from my 2000 Sv650. Can't find much help so I rented a pulley gear puller thinking it would easily take it off. Well it did, except for the part still mounted to the crankshaft. (See pictures) I doubt I can piece it back together where...
  9. SV650 Gen1 (99-02) Tech
    Hi all, my 650 has done 14 thou in 20 years. Bought it last summer but didnt ride it much. This year it started leaking fuel so I checked float cutoff - "o" rings were gone on the brass holder - new "o's"and a new gauze on the top plus clean out of gunk fixed that. Now is the bike is great from...
  10. SV650 Gen1 (99-02) Tech
    Previously on my bike is F'd Went out for small cruise, heard large pop power died. Battery blew. Jump started, spit and sputtered for a hundred feet then completely died. NEW PARTS: So far I've changed the R/R to a MOSFET one. CDI box. Battery Relay box next to fuzes($3 part has lots of...
  11. SV650 Gen1 (99-02) Tech
    So I went for a ride today(still out waiting on a tow) while riding at roughly 3k rpm I heard a large pop bike lost power for a second lights all flashed so I pulled in the clutch went into a parking lot and shut the bike off smelled like rotten eggs wasn't leaking oil or anything lifted the...
  12. SV650 Gen1 (99-02) Tech
    I'm new to riding and I just recently purchased a track bike that was in the works of becoming street legal. From the information I have the 1st owner put the 2gen intake cams in the exhaust cam section and some emulators for the front shocks for dampening the micron exhaust a fiberglass tail...
  13. SV650 Gen1 (99-02) Tech
    So as the title says, I tried adjusting the chain without a rear-wheel stand since the manual didn't mention needing one, but the main mistake was not loosening the axle nut while gripping the nug on the other end. The chain adjuster on the kick stand's side tightened accordingly but when I went...
1-14 of 14 Results
Top